Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - Matthew

#1
Well, I got the pump back together, bled it, the filters and at the injectors and it pretty much started right up after a small toot of ether. It is running well. I used it for about an hour today pushing back a large pile of brush. I replaced all of the o-rings in the pump, some of which I had, some I got from the hardware store and one I ordered on line. I made a new gasket for the top cover and left the front seal in place as this had been replaced by the previous owner not so long ago and looked OK.  I wouldn't be afraid to go thru another pump if I had a good manual to go by. It seems with the newer pumps you can pick up a sealing kit containing all of the O-rings for not too much.  Thanks again for the input.
#2
I had to open a new topic on this Jensales manual as when I tried to reply I was "Flagged as spam?" I will try again
Well, I guess I am on the other side of the ball on this one. I got Jensales manuals with my AD when I bought it and they seemed fine for helping me fix it up. I don't have them here with me but as I remember they were pretty clear and I was impressed to have manuals with it. I just ordered a manual for the injector pump on my AD from Jensales  since the repair manual didn't get into disassemble of the pump itself. I was happy to find a manual for this old pump and although there are few pic's they are clear and I would say it is a good copy. It did come with a money back guarantee if I was not satisfied.  Original manuals are nice but so far I have had luck with these nanuals
#3
Well, I guess I am on the other side of the ball on this one. I got Jensales manuals with my AD when I bought it and they seemed fine for helping me fix it up. I don't have them here with me but as I remember they were pretty clear and I was impressed to have manuals with it. I just ordered a manual for the injector pump on my AD from Jensales  since the repair manual didn't get into disassemble of the pump itself. I was happy to find a manual for this old pump and although there are few pic's they are clear and I would say it is a good copy. It did come with a money back guarantee if I was not satisfied.  Original manuals are nice but so far I have had luck with these nanuals.
#4
Well, I guess I am on the other side of the ball on this one.  The manuals I got with my AD were Jensales for both repair and parts and I used them for fixing what the crawler needed without a problem. I don't have them right here to recheck but I remember them having decent pic's. I just bought a manual from Jensales for the injector pump on the AD since the repair manual doesn't get into it's disassemble and I was happy just to find a manual for this old pump. There are not to many pictures but what is there is clear.  I would say it was a nice reprint. It did  come with a guarantee for my money back if not satisfied. It is nice to have the original but a Good copy should work.
#5
Well, it has been a while and after have determined that the problem must be internal to the pump. Talked with pump rebuild facility and the tech was helpful but said for this pump the best that really can be done is a tear down, inspection, cleaning and resealing if everything is ok, no new parts left for this old pump. I was able to locate a manual and now have the pump completely apart in my basement. Manual has been great so far. Pump looks to be in pretty good condition considering it's age but had a lot of mud coating all of the parts. I am not sure if it is from the fuel or maybe rust dust that came from the tank and got by the filters? It doesn't appear to be abrasive and I am cleaning it off all of the parts. Pistons were stuck in bores both in the main pressure part of the pump and the transfer pump so I am hoping that is my problem. I hope to get it back together and working. I felt I really didn't have anything to lose just time and I am learning some things. I will let you all know how I make out. Thanks for the input.
#6
I have a AD dozer that won't start up this year, not pumping fuel I believe.  Had the same problem last year and I changed the filters which were awful and after a lot of bleeding and some help from this forum about bleeding at the injectors I got it going and it started well the next few times I started it last year.  I shut the fuel off over winter at there was some leakage at the injector pump "Roosemaster" and now I am having problems again. The gasket for the top cover of the pump was poking out and leaking and I couldn't get fuel to come out at the bleed screw on top of the cover. I had to pull the pump as I couldn't get the cover off installed. I pulled the pump, removed the top cover which looks kind of like a small valve cover and made a new gasket for it. I reinstalled the pump, bled the filters and lines but can't get fuel to bleed out at the injectors when I crack the lines. I do have fuel coming out of the bleed screw on top of the injector cover now. Any suggestions? Thanks
#7
I will upload some pic's of my dozer if I can figure out how. Thanks
#8
Thanks for all of the input guys, I got her running, bleeding the injector lines was the trick. I am not sure what  originally was the problem with the no start, maybe clogged fuel filters or something stuck in the injector pump but in the end after replacing the filters I guess I just wasn't getting all  of the air out. I ran it a bit today and will go back in a few days and try again but I think it will start ok now. I appreciate your help.
#9
No, I haven't tried bleeding the injector lines but will try that next time I am at machine which is about 40 minutes from where I live. Machine did not die, I last used it to push back some brush piles and ran it for about 30-45 minutes and then shut it down. It sat for about a week or two and then wouldn't start. It sat all winter and started up this summer fine. There is no separate shut off for this injector pump just the throttle lever which when pushed forward fully shuts off fuel and kills engine. I am thinking something internal to pump may be sticking but I will try bleeding the injector lines as you suggest. Unfortunately I can't warrant having the pump rebuilt on this tractor so I have to try to get it running as best I can. Thankyou for your help and input.
#10
I have a 1956 ADH which I can't get to start and hope that maybe someone could give me some advise. I have had the crawler a few years and done a bit of work to it. It is fairly worn, smokes a bit but has always started for me until now. It appears not to be getting fuel, little or no smoke from stack. Fuel filters hadn't been changes in a long time so I started there. Cleaned out canisters real good, put in new filters, bleed system but no go. It has the Roosemaster pump, pump is full of fuel. I found small bleeder on top of pump and fuel comes out when I removed this. I am thinking something internal in pump stuck in the off, fuel closed position? I removed small valve cover looking top on injector pump hoping I could see something, hard to do with pump on engine and working thru dozer arms. I couldn't get cover off all of the way and after moving some parts inside put it back on, bled and tried to start but no go. I am thinking of pulling pump so that I can work on it on the bench. Any ideas here? Can something stick in the closed or fuel off position? Thanks