Fan belt for E or AG

Started by Blake Malkamaki, October 23, 2007, 01:07:46 AM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

Blake Malkamaki

Does anyone have the part number or measurements for a fan belt for a model E (or AG) with no generator? The belt just goes from the crankshaft to the fan.

Mine broke yesterday when Bob and I took it for a cruise around the farm. Really, it was all Bob's fault!! The fact that the belt was old, cracked and coming apart couldn't have had anything to do with it. It just had to be Bob!  :wink:

Blake
My gramps Howard van Driest was Experimental Engineer at Cletrac and Oliver Corporation. After the plant closed, he and my uncle started an excavating business, initially using Cletrac and Oliver Crawler tractors. Please help Support This Site and give your business exposure by buying a business card sized ad.

clueless

#1
Wellll...I've got a few catalogs, and for a change they generally agree, altho they don't say much...
39 World Super Service shows C20, AG,E,EW with Herc OOC, for 36 only, OE# 15227, their #V-248...
47 Raybestos shows AG,AGH,AG3  (eng ID omitted), 1930-40, OE# 15227, their #V-518X..ALSO E,E31,E38,E42,E62 with Herc OOC, 1936-38, OE#15227,  their #V-518X  (and many other E Series also listed);
50 Gates  shows AG,AG3 with Herc OOC 1930-42 "Fan" OE#15227, their #8503TR..BUT ALSO SHOWS "Fan 45 in belt" OE#90022, their 168TG (AG6,AG6H shows a Cont F-226 with "fan" and "fan and gen")...AND ALSO SHOWS" E Series,E38,E42,E62,E68,E76" with the #15227/8503TR.
NONE of the #15227 listings have any "fan/fan-gen/wtr pump" notes.
I strongly suspect you'll be doing what's all too often done: take the old belt in and try to match it's length!
Believe me, since I've been acquiring these, I have a lot more sympathy for the parts-counter people!!
Nothing here is what it appears to be!

Bob

#2
it was all a setup for sure! :roll:
Certified Cletrac-tard

clueless

#3
Couldn't get to sleep (2AM here: Portland, OR); sitting in front of this box and remembered I should've  included the dimensions...
1939 World Super Service (Continental Products, Inc, Chicago) says their V-248 has 35.8 IC and 25/32 top....
1947 Raybestos says their V-518X has 391/4 OC and weighs approx 101/2 oz
1950 Gates says their 8503TR has 391/4 OC, 25/32 top and 44 degree slope.
At least that matches fairly well; can't say the same about the cross index listings in the 39 and 47 (the 50 has none):out of 12 brands that listed the numbers only four matched both ways, the rest giving numbers that didn't show in the Cletrac listings...but in their defense, a couple of the new numbers I checked had OC's only a quarter or half inch different.
I'm going back to bed; tossing and turning's still better than wondering why the numbers dont't match better.  With sympathy,  Bud
Nothing here is what it appears to be!

Blake Malkamaki

#4
Thanks Clueless...

I'm going to measure the belt I have and compare it to your numbers. The one I have that was on it is too narrow, though it worked, but rode too low in the vee on the pulleys.

Blake
My gramps Howard van Driest was Experimental Engineer at Cletrac and Oliver Corporation. After the plant closed, he and my uncle started an excavating business, initially using Cletrac and Oliver Crawler tractors. Please help Support This Site and give your business exposure by buying a business card sized ad.